<meter id="pryje"><nav id="pryje"><delect id="pryje"></delect></nav></meter>
          <label id="pryje"></label>

          新聞中心

          EEPW首頁 > 嵌入式系統 > 設計應用 > 基于POWR1220AT8設計的12V熱插拔技術

          基于POWR1220AT8設計的12V熱插拔技術

          作者: 時間:2010-06-22 來源:網絡 收藏
          ispPAC-集成了在系統可編程邏輯和在系統可編程模擬功能,是通用的電源監視器,順序和余量控制器,它提供12個單獨的模擬輸入通道,用來監視多達12個電源測試點. 提供和IPMC標準的命令接口,能把板上的DC/DC轉換器轉換成精密的數控電源.本文介紹了ispPAC-主要特性,方框圖,以及應用方框圖, 評估板外形圖,采用ispPAC-POWR1220AT8的熱插拔控制器參考電路圖.


          ispPAC-POWR1220AT8典型應用:

          The Power Manager II POWR1220AT8 provides a standard command interface to the IPMC while performing FRU specific payload power management functions using the on-chip CPLD. The POWR1220AT8 also converts all on board DC-DC converters into accurate digitally controlled supplies.


          圖1.ispPAC-POWR1220AT8方框圖

          圖2.ispPAC-POWR1220AT8應用方框圖

          圖3.ispPAC-POWR1220AT8提高DC/DC轉換器精度的應用方框圖

          The PAC-POWR1220AT8 evaluation board allows the designer to quickly configure and evaluate the ispPAC-POWR1220AT8 device on a fully assembled printed-circuit board. The four-layer board supports a 100-pin TQFP package, pads for user I/O, a JTAG programming cable connector, and a connector for the device’s I2C interface. JTAG programming signals can be generated by using an ispDOWNLOAD® programming cable connected between the evaluation board and a PC. Both analog and digital features of the ispPACPOWR1220AT8 device can be easily configured using PAC-Designer® software.

          The PAC-POWR1220AT8 evaluation board is available in a Development Kit that includes:

          PAC-POWR1220AT8 Evaluation Board

          ispDOWNLOAD Cable

          AC Adapter (International plugs)

          User Documentation

          圖4.ispPAC-POWR1220AT8評估板外形圖

          采用ispPAC-POWR1220AT8的熱插拔控制器參考

          A hot swap controller is used to limit the inrush current when a circuit board is plugged into a powered backplane.

          In addition, a hot swap controller may offer some or all of the following features: over-current protection (electronic circuit breaker), over-voltage protection, and under-voltage protection. Hot swap controllers are also required to isolate the board from the backplane which is useful in troubleshooting, maintenance, and upgrade activities. The power-down request may come from the backplane (remote) or an on-board switch (manual).

          This document describes how a Lattice Power Manager II ispPAC®-POWR1220AT8 can be used to implement the functions required for hot swap applications. This reference design is targeted to operate on the Power Manager Hercules Development Kit (PAC-POWR1220AT8-HS-EVN C Standard or PAC-POWR1220AT8-HA-EVN CAdvanced).

          上一頁 1 2 下一頁

          評論


          相關推薦

          技術專區

          關閉
          看屁屁www成人影院,亚洲人妻成人图片,亚洲精品成人午夜在线,日韩在线 欧美成人 (function(){ var bp = document.createElement('script'); var curProtocol = window.location.protocol.split(':')[0]; if (curProtocol === 'https') { bp.src = 'https://zz.bdstatic.com/linksubmit/push.js'; } else { bp.src = 'http://push.zhanzhang.baidu.com/push.js'; } var s = document.getElementsByTagName("script")[0]; s.parentNode.insertBefore(bp, s); })();