用VB6.0數字示波單片機實時監測數據的一種方法

三．軟件設計思想（一個具體的例）

要求：單片機每1秒串行發送給PC一幀十位數據，VB6.0波形動態顯示數據。

設計：通過窗體Load事件程序完成如圖3所示界面設計，使得程序一運行即出現該界面，單擊接收數據按鈕，通過MsComm控件接收串行通信數據并波形動態顯示。顯示時一屏12個數據，每次接收了新數據后，數組中的數據依次后移，既a(0)（假設為數組a(11)）放最新接收的數據，原a(11)中的數據被移出而移入原a(10)中的數。每次有新數據移入并且有原數據移出時，先清屏再復原背景顯示數據，造成數據平移視覺效果。

設計時波形一定要從界面最左端入，從最右端出，這樣動態平移視覺效果才好。窗體的AutoRedraw屬性要設為True.

四．軟件設計源程序(波形參見圖4、圖5)
'定義所用變量
Dim a(11) As Single
Dim d As Integer
Dim n As Integer
Dim m As Integer
Dim Buffer As Variant
Private Sub Form_Load()
'一屏顯示的12個數賦初值0
For i = 0 To 11
a(i) = 0
Next i
'定義坐標原點
Form1.Scale (-10, 250)-(220, -15)
'畫X、Y軸
Line (0, 0)-(220, 0)
Line (0, 0)-(0, 250)
'加坐標刻度和數值
CurrentX = 200: CurrentY = 13: Print X(s)
CurrentX = 5: CurrentY = 245: Print Y(V)
For i = 0 To 220 Step 20
CurrentX = i: CurrentY = 3: Line -(i, 0)
If i = 200 Then CurrentX = i - 7 Else CurrentX = i - 12
CurrentY = 0: Print i Mod 19
Next i
For i = 0 To 210 Step 20
If i > 0 Then
CurrentX = -14: CurrentY = i: Print i / 10
CurrentX = 230: CurrentY = i: Line -(0, i)
End If
Next i
'mscomm控件初始化
MSComm1.CommPort = 1
MSComm1.Settings = 9600,n,8,1
MSComm1.InputMode = comInputModeBinary
MSComm1.InputLen = 0
MSComm1.RThreshold = 0
End Sub
'接收并顯示數據
Private Sub Command1_Click()
'無條件循環接收數據
Do