AT89S52單片機模擬I2C總線協議讀寫AT24C04

AT24C04是具有I2C總線接口的EEPROM.大小為512*8bit.單片機AT89S52本身不具有I2C總線結口,所以可編寫程序用并行端口模擬I2C總線協議讀寫AT24C04.

多個設備通信的重點（１．電平的區別，如串口通信中ＰＣ與單片機通信,PC機串口電平值為+12V~-12V，單片機為ＴＴＬ電平0V~+5V.，所以要用電平轉換芯片轉電平．２，通信協議．（串口通信協議））

具體的協議內容與數據格式可查資料.

代碼如下:

#include

#define WriteDeviceAddress 0xa0
#define ReadDeviceAddress 0xa1

sbit SCL = P3^4;
sbit SDA = P3^5;
sbit DOG = P0^0;
sbit PP = P0^1;
sbit DOG1 = P0^7;

void DelayMs(unsigned int number)
{
unsigned char tmp;
for(;number!=0;number--,DOG1=!DOG1)
{
for(tmp=112;tmp!=0;tmp--)
{
}
}
}

void Start()
{
SDA = 1;
DelayMs(1);
SCL = 1;
DelayMs(1);
SDA = 0;
DelayMs(1);
SCL = 0;
DelayMs(1);
}

bit Write8bit(unsigned char input)
{
unsigned char tmp;
for(tmp =8;tmp!=0;tmp--)
{
SDA = (bit)(input&0x80);
DelayMs(1);
SCL = 1;
DelayMs(1);
SCL = 0;
DelayMs(1);
input = input << 1;
}
return 1;
}

bit TestAck()
{
bit ErrorBit;
SDA = 1;
DelayMs(1);
SCL = 1;
DelayMs(1);
ErrorBit = SDA;
DelayMs(1);
SCL = 0;
DelayMs(1);
return(ErrorBit);
}

void Stop()
{
SCL = 0;
DelayMs(1);
SDA = 0;
DelayMs(1);
SCL = 1;
DelayMs(1);
SDA = 1;
DelayMs(1);
}

void WriteI2C(unsigned char *Wdata, unsigned char RomAddress, unsigned char number)
{
Start();
Write8bit(WriteDeviceAddress);
TestAck();
Write8bit(RomAddress);
TestAck();
for(;number!=0;number--)
{
Write8bit(*Wdata);
TestAck();
Wdata++;
}
Stop();
DelayMs(1);
}

unsigned char Read8Bit()
{
unsigned char tmp,rbyte = 0;
for(tmp=8;tmp!=0;tmp--)
{
SCL = 1;
DelayMs(1);
rbyte = rbyte << 1;
DelayMs(1);
rbyte = rbyte|((unsigned char)(SDA));
SCL = 0;
DelayMs(1);
}
return(rbyte);
}

void Ack()
{
SDA = 0;
DelayMs(1);
SCL = 1;
DelayMs(1);
SCL = 0 ;
DelayMs(1);
SDA = 1;
DelayMs(1);
}

void NoAck()
{
SDA = 1;
DelayMs(1);
SCL = 1;
DelayMs(1);
SCL = 0 ;
DelayMs(1);
}
void ReadI2C(unsigned char* RamAddress,unsigned char RomAddress,unsigned char bytes)
{
Start();
Write8bit(WriteDeviceAddress);
TestAck();
Write8bit(RomAddress);
TestAck();
Start();
Write8bit(ReadDeviceAddress);
TestAck();
while(bytes != 1)
{
*RamAddress = Read8Bit();
Ack();
RamAddress++;
bytes--;
}
*RamAddress = Read8Bit();
NoAck();
Stop();
}

void main()
{
unsigned char writeByte[8] = {0xC0,0X34,0X12,0X22,0X11,0X01,0X00,0X00};

unsigned char readByte[8];

unsigned char *addw;
unsigned char *addr;

unsigned char i;
unsigned char ok = 0;

bit write = 1;
DOG = 1;

while(1)
{
if(write == 1)
{
addw = writeByte;
addr = readByte;
WriteI2C(addw,0x00,8);
ReadI2C(addr,0x00,8);
for(i=0;i<8;i++)
{
if(writeByte[i] == readByte[i])
{
ok++;
}
}
if(ok == 8)
{
DOG = 0; //一樣P0.0亮

}
else
{
PP = 0; //不一樣P0.1亮
}
write = 0;
}
}
}