如何利用ARM里的PWM模塊產生SPWM波

利用PWM模塊產生SPWM波，主要是利用了PWM模塊里一個比較器中斷功能。通過比較器，產生一個中斷，再附值產生一個PWM脈沖，一直循環，下去，通過附不同的值，就可以產生一個SPWM了。主要程序如下：

const INT16U spwmwidth[spwmct]={24,72,120,168,215,262,308,353,398,441,484,525,565,604,641,677,
711,743,774,803,829,854,877,897,916,932,946,958,967,974,979,981,
981,979,974,967,958,946,932,916,897,877,854,829,803,774,743,711,
677,641,604,565,525,484,441,398,353,308,262,215,168,120,72,24
};

void SpwmInit(void)
{

SysCtlPWMClockSet(SYSCTL_PWMDIV_64); // PWM時鐘源64分頻

SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOD); // 使能PD口外設

SysCtlPeripheralEnable(SYSCTL_PERIPH_PWM); // 使能PWM外設

GPIOPinTypePWM(GPIO_PORTD_BASE, GPIO_PIN_0 | GPIO_PIN_1);// 設置PD0,PD1為PWM0和PWM1

PWMGenConfigure(PWM_BASE, PWM_GEN_0, // 設置PWM發生器0為上下計數方式，兩路PWM不同步
PWM_GEN_MODE_UP_DOWN | PWM_GEN_MODE_NO_SYNC | PWM_GEN_ACT_ZERO | PWM_GEN_ACT_ONE <<6);
//PWM0A 在計數器為0時，輸出 為低電平，與比較器A值相等時輸出為高電平 。

PWMOutputInvert(PWM_BASE, PWM_OUT_0_BIT | PWM_OUT_1_BIT,true); //設置PWM兩路反相

PWMGenPeriodSet(PWM_BASE, PWM_GEN_0, 1000); // 設置兩路PWM的共同周期

PWMDeadBandEnable(PWM_BASE,PWM_GEN_0,15,15); //死區時間設置

PWMPulseWidthSet(PWM_BASE, PWM_OUT_0, spwmwidth[16]); // 分別設置兩路PWM的匹配值

// PWMPulseWidthSet(PWM_BASE, PWM_OUT_1, 1000);

PWMOutputState(PWM_BASE, PWM_OUT_0_BIT | PWM_OUT_1_BIT, true);// 使能PWM0和PWM1

PWMGenEnable(PWM_BASE, PWM_GEN_0); // 使能PWM發生器0
HWREG(PWM_BASE+0X044)|=0x01;
// PWMGenIntRegister(PWM_BASE, PWM_GEN_0,*SpwmISRHandler) ;

PWMIntEnable(PWM_BASE,PWM_INT_GEN_0); //中斷使能 WM發生器0模塊
IntEnable(INT_PWM0);
}

#endif

/***********中斷程序*****************************************************************************/
void SpwmISRHandler (void)
{

static INT16U count;

#if OS_CRITICAL_METHOD == 3
OS_CPU_SR cpu_sr;
#endif

OS_ENTER_CRITICAL();
OSIntNesting++;
OS_EXIT_CRITICAL();

PWMGenIntClear(PWM_BASE, PWM_GEN_0,PWMIntStatus(PWM_BASE, true)|PWM_INT_GEN_0 );//清除中斷
PWMPulseWidthSet(PWM_BASE, PWM_OUT_0, spwmwidth[count]);
if (count>=63||count<=0 ){
count=1 ;
}
else {
count++;
}

OSIntExit();
}