MSP430串口接收發送中斷程序

#include <msp430x14x.h>

unsigned char RecBuf[255]; //接收數據緩存
unsigned char *SDat; //指向要發送的數據
unsigned char Rindex; //接收數據計數
unsigned char Tindex; //發送數據計數
unsigned char SendLen; //發送數據長度

void ConfigUart0()
{
P3SEL |= 0x30; // 選擇P3.4和P3.5做UART通信端口
ME1 |= UTXE0 + URXE0; // 使能USART0的發送和接受
UCTL0 |= CHAR; // 選擇8位字符

UTCTL0 |= SSEL1; // UCLK = SMCLK
UBR00 = 0xD0; // 波特率9600
UBR10 = 0x00; //
UMCTL0 = 0x40; // Modulation
UCTL0 &= ~SWRST; // 初始化UART狀態機
IE1 |= URXIE0 + UTXIE0; // 使能USART0的收發中斷
}

void main(void)
{
unsigned int i;

WDTCTL = WDTPW + WDTHOLD; // 關閉看門狗
BCSCTL1 &= ~XT2OFF; //使TX2有效，TX2上電默認是關閉的
do
{
IFG1 &= ~OFIFG; //清除振蕩器失效標志
for(i=0xff;i>0;i--); //延時，待穩定
}
while((IFG1 & OFIFG)!=0); //若振蕩器失效標志有效
BCSCTL2 |= SELM1; //使MCLK=XT2
BCSCTL2 |= SELS+DIVS1; //SMCLK=XT2,4分頻，即2MHZ

BoardConfig(0xb8); // 關閉數碼管、流水燈和電平轉換
ConfigUart0(); //配置UART0
_EINT(); //打開全局中斷

while(1)
{
LPM1;
}
}

#pragma vector = UART0RX_VECTOR
__interrupt void UART0_RXISR(void)
{
RecBuf[Rindex++] = RXBUF0;
if(RecBuf[Rindex-1]==0xfe) //接收完畢
{
SendLen = Rindex;
Rindex=0;
if(RecBuf[0]==0xfd) //幀頭正確
{
LPM1_EXIT;
SDat = RecBuf;
IFG1 |= UTXIFG0; // 設置中斷標志，進入發送中斷程序
}
}
}

#pragma vector = UART0TX_VECTOR
__interrupt void UART0_TXISR(void)
{

if(Tindex < SendLen)
{
TXBUF0 = *(SDat+Tindex);
Tindex++;
}
else
{
Tindex=0;
//LPM1;
}

}