<meter id="pryje"><nav id="pryje"><delect id="pryje"></delect></nav></meter>
          <label id="pryje"></label>

          新聞中心

          EEPW首頁 > 嵌入式系統 > 設計應用 > AVR單片機的SPWM程序

          AVR單片機的SPWM程序

          作者: 時間:2016-11-24 來源:網絡 收藏
          #include//程序中現在只有SPWM產生的相關的程序,其他的程序都已經刪除

          #include

          本文引用地址:http://www.ex-cimer.com/article/201611/320604.htm

          #pragma interrupt_handler T0:17 //定時器0的溢出中斷向量


          unsigned int SPWM_OCR1A[101]={493,492,491,490,489,488,487,486,485,484,
          483,482,481,479,478,477,476,475,474,473,
          472,471,470,469,468,467,466,465,464,463,
          462,462,461,460,459,458,457,456,455,454,
          453,452,451,450,449,448,448,447,446,445,
          444,443,442,441,440,440,439,438,437,436,
          435,434,434,433,432,431,430,429,429,428,
          427,426,425,424,424,423,422,421,420,420,
          419,418,417,416,416,415,414,413,413,412,
          411,410,410,409,408,407,407,406,405,404,404,};
          //數組里面的值分別對應于從45.0~55.0HZ的OCR1A的值,(將每個周期分成360份,即每一度為一份)步進為0.1HZ 在寫程序的時候,
          //只要將OCR1A的值替換成以上相應的值就可以得到,對應于正弦波的相應的頻率
          double SPWM_sin_value[360]={1.0174,1.0348,1.0523,1.0697,1.0871,1.1045,1.1218,1.1391,1.1564,1.1736,1.1908,1.2079,1.2249,1.2419,
          1.2588,1.2756,1.2923,1.309,1.3255,1.342,1.3583,1.3746,1.3907,1.4067,1.4226,1.4383,1.4539,1.4694,1.4848,1.4999,
          1.515,1.5299,1.5446,1.5591,1.5735,1.5877,1.6018,1.6156,1.6293,1.6427,1.656,1.6691,1.6819,1.6946,1.7071,1.7193,
          1.7313,1.7431,1.7547,1.766,1.7771,1.788,1.7986,1.809,1.8191,1.829,1.8386,1.848,1.8571,1.866,1.8746,1.8829,1.891,
          1.8987,1.9063,1.9135,1.9205,1.9271,1.9335,1.9396,1.9455,1.951,1.9563,1.9612,1.9659,1.9702,1.9743,1.9781,1.9816,
          1.9848,1.9876,1.9902,1.9925,1.9945,1.9961,1.9975,1.9986,1.9993,1.9998,2,1.9998,1.9993,1.9986,1.9975,1.9961,1.9945,
          1.9925,1.9902,1.9876,1.9848,1.9816,1.9781,1.9743,1.9702,1.9659,1.9612,1.9563,1.951,1.9455,1.9396,1.9335,1.9271,
          1.9205,1.9135,1.9063,1.8987,1.891,1.8829,1.8746,1.866,1.8571,1.848,1.8386,1.829,1.8191,1.809,1.7986,1.788,1.7771,
          1.766,1.7547,1.7431,1.7313,1.7193,1.7071,1.6946,1.6819,1.6691,1.656,1.6427,1.6293,1.6156,1.6018,1.5877,1.5735,
          1.5591,1.5446,1.5299,1.515,1.5,1.4848,1.4694,1.4539,1.4383,1.4226,1.4067,1.3907,1.3746,1.3583,1.342,1.3255,1.309,
          1.2923,1.2756,1.2588,1.2419,1.2249,1.2079,1.1908,1.1736,1.1564,1.1391,1.1218,1.1045,1.0871,1.0697,1.0523,1.0348,
          1.0174,1,0.9825,0.9651,0.9476,0.9302,0.9128,0.8954,0.8781,0.8608,0.8435,0.8263,0.8091,0.792,0.775,0.758,0.7411,
          0.7243,0.7076,0.6909,0.6744,0.6579,0.6416,0.6253,0.6092,0.5932,0.5773,0.5616,0.546,0.5305,0.5151,0.5,0.4849,0.47,
          0.4553,0.4408,0.4264,0.4122,0.3981,0.3843,0.3706,0.3572,0.3439,0.3308,0.318,0.3053,0.2928,0.2806,0.2686,0.2568,0.2452,
          0.2339,0.2228,0.2119,0.2013,0.1909,0.1808,0.1709,0.1613,0.1519,0.1428,0.1339,0.1253,0.117,0.1089,0.1012,0.0936,
          0.0864,0.0794,0.0728,0.0664,0.0603,0.0544,0.0489,0.0436,0.0387,0.034,0.0297,0.0256,0.0218,0.0183,0.0151,0.0123,
          0.0097,0.0074,0.0054,0.0038,0.0024,0.0013,0.0006,0.0001,0,0.0001,0.0006,0.0013,0.0024,0.0038,0.0054,0.0074,0.0097,
          0.0123,0.0151,0.0183,0.0218,0.0256,0.0297,0.034,0.0387,0.0436,0.0489,0.0544,0.0603,0.0664,0.0728,0.0794,0.0864,0.0936,
          0.1012,0.1089,0.117,0.1253,0.1339,0.1428,0.1519,0.1613,0.1709,0.1808,0.1909,0.2013,0.2119,0.2228,0.2339,0.2452,
          0.2568,0.2686,0.2806,0.2928,0.3053,0.318,0.3308,0.3439,0.3572,0.3706,0.3843,0.3981,0.4122,0.4264,0.4408,0.4553,
          0.47,0.4849,0.4999,0.5151,0.5305,0.546,0.5616,0.5773,0.5932,0.6092,0.6253,0.6416,0.6579,0.6744,0.6909,0.7076,0.7243,
          0.7411,0.758,0.775,0.792,0.8091,0.8263,0.8435,0.8608,0.8781,0.8954,0.9128,0.9302,0.9476,0.9651,0.9825,0.9999,};


          unsigned int M=100;

          void PORT_inti() // 端口初始化
          {
          DDRA=0xff;
          PORTA=0x00;
          DDRB=0xff; // B,D,E端口為輸出
          PORTB=0x00; // 端口剛開始的值都是0,或者說是都不帶上拉電阻
          DDRD=0xff;
          DDRE=0x00;
          PORTD=0x00;
          PORTE=0x00;
          DDRF=0X00; // AD轉換端口
          PORTF=0X00;
          DDRG=0X07;
          DDRC=0X00;
          }

          void TO_inti() //定時器0的初始化
          {
          TCCR0=0x02; // 8分頻
          TCNT0=0x9C; // 確定中斷的時間,0.05ms中斷一次
          TIMSK|=BIT(0); // T/C0 溢出中斷使能
          }


          void T1_inti()
          {
          TCNT1H=0xfc; //計數器清零
          TCNT1L=0xe0;
          TCCR1A=0x2d; // 0010 1101 頻率相位修正PWM,發生匹配的時候,電平為0
          TCCR1B=0x11; // 0001 0001 不分頻,要是分頻的話開關頻率就達不到那么高了
          TCCR1C=0x00; //沒什么作用
          OCR1A=493; // 在這種模式下 最大值寄存器OCR1A中的值,這個值與方波的頻率有關系,還和方波的占空比有關系
          }

          void T0() //在定時器0的中斷程序中向OCR1A和OCR1B送正弦函數表中的數值,調節M和OCR1A的值就可以調節頻率和幅度
          {

          if(count<360)
          {
          OCR1B=SPWM_sin_value[count]*M+OCR1A/2-M;//公式應該是OCR1A=OCR1A/2+M(SPWM_sin_value[count]-1)其中OCR1A是三角波的最大值,M為振幅調節系數范圍是0~OCR1A/2,(SPWM_sin_value[count]-1)中減的一是應為做的正弦表是一個全正的表,現在要變成(-1~+1)之間的表,調節OCR1A的值可以調節開關頻率,調節M的值克一調節相關方波的占空比
          OCR1C=SPWM_sin_value[count]*M+OCR1A/2-M
          count++;
          }
          else
          count=0;
          TCNT0=0x9C;//可以進一步縮短所用的時間,這樣可以達到更好的傳送效果,但是也更加占用單片機的時鐘資源。
          }

          void main()
          {
          PORT_inti(); //端口初始化
          TO_inti(); //產生 kHZ的開關頻率
          T1_inti(); //相位修正PWM用于產生兩路的SPWM波
          while(1) //死循環 ,等待中斷
          {
          }
          }



          關鍵詞: AVR單片機SPWM程

          評論


          技術專區

          關閉
          看屁屁www成人影院,亚洲人妻成人图片,亚洲精品成人午夜在线,日韩在线 欧美成人 (function(){ var bp = document.createElement('script'); var curProtocol = window.location.protocol.split(':')[0]; if (curProtocol === 'https') { bp.src = 'https://zz.bdstatic.com/linksubmit/push.js'; } else { bp.src = 'http://push.zhanzhang.baidu.com/push.js'; } var s = document.getElementsByTagName("script")[0]; s.parentNode.insertBefore(bp, s); })();