STM32之PWM最終版－注釋明了一看就懂

void GPIO_TimPWM(void)

{

GPIO_InitTypeDef GPIO_InitStructure;

RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA , ENABLE);//

GPIO_InitStructure.GPIO_Pin = GPIO_Pin_7; //TIM_CH2 GPIOA_Pin_7輸出

GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP; //復用推挽輸出

GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;

GPIO_Init(GPIOA, &GPIO_InitStructure); //不解釋
}

void TIM3_Configuration(void)

{

TIM_TimeBaseInitTypeDef TIM_TimeBaseStructure;

TIM_OCInitTypeDef TIM_OCInitStructure;

RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM3, ENABLE); //使能TIM3

//假如我要產生50Hz占空比為50%的PWM波，方便控制舵機

//設置方法：

//系統默認時鐘為72MHz，預分頻71+1次，得到TIM3計數時鐘為1MHz
//計數長度為19999+1=20000，可得PWM頻率為1M/20000=50Hz

//具體設置可參考上面的設置方法，簡單明了！

TIM_TimeBaseStructure.TIM_Prescaler =72-1;//網上多數設置有誤

TIM_TimeBaseStructure.TIM_Period =20000-1;

TIM_TimeBaseStructure.TIM_ClockDivision = TIM_CKD_DIV1;

//設置時鐘分割:TIM_CKD_DIV1 = 0，PWM波不延時（延時破壞占空比？待考證）

TIM_TimeBaseStructure.TIM_CounterMode = TIM_CounterMode_Up; //TIM向上計數模式

TIM_TimeBaseInit(TIM3, &TIM_TimeBaseStructure);

TIM_ARRPreloadConfig(TIM3, DISABLE); //禁止ARR預裝載緩沖器,也可以不用設置

TIM_OCInitStructure.TIM_OCMode = TIM_OCMode_PWM2; //選擇定時器模式:TIM脈沖寬度調制模式2

TIM_OCInitStructure.TIM_OutputState = TIM_OutputState_Enable; //比較輸出使能

//占空比設置方法：

//占空比=(TIM_Pulse+1)/(TIM_Pulse+1)-(TIM_Period+1)=10000/20000=0.5=50%

TIM_OCInitStructure.TIM_Pulse =10000-1;

TIM_OCInitStructure.TIM_OCPolarity = TIM_OCPolarity_High; //輸出極性:TIM輸出比較極性高

TIM_OC2Init(TIM3, &TIM_OCInitStructure); //根據TIM_OCInitStruct中指定的參數初始化外設TIMx

TIM_OC2PreloadConfig(TIM3, TIM_OCPreload_Enable); //使能TIMx在CCR2上的預裝載寄存器

//上面兩句中的OC2確定了是channle幾，要是OC3則是channel 3

TIM_CtrlPWMOutputs(TIM3,ENABLE); //設置TIM2的PWM輸出為使能

TIM_ARRPreloadConfig(TIM3, ENABLE); //使能TIMx在ARR上的預裝載寄存器

TIM_Cmd(TIM3, ENABLE); //使能TIMx外設

}

int main(void)

{

GPIO_TimPWM();

TIM3_Configuration();

while(1)

{

} ;

}

利用Keil邏輯分析儀分分析PWM波形圖：經過測試可以看出輸出波形精度可靠！