<meter id="pryje"><nav id="pryje"><delect id="pryje"></delect></nav></meter>
          <label id="pryje"></label>

          新聞中心

          EEPW首頁 > 嵌入式系統 > 設計應用 > STM32--USB詳細使用說明

          STM32--USB詳細使用說明

          作者: 時間:2016-11-27 來源:網絡 收藏

          uint8_t Out0_Process(void)
          {
          uint32_t ControlState = pInformation->ControlState;

          if ((ControlState == IN_DATA) || (ControlState == LAST_IN_DATA))
          {

          //主機在完成傳輸前終止傳輸
          ControlState = STALLED;
          }
          else if ((ControlState == OUT_DATA) || (ControlState == LAST_OUT_DATA))
          {
          DataStageOut();
          ControlState = pInformation->ControlState;
          }

          else if (ControlState == WAIT_STATUS_OUT)//進入到這個里面
          {
          (*pProperty->Process_Status_OUT)();//這個函數其實什么也沒做
          #ifndef STM32F10X_CL
          ControlState = STALLED;//狀態變成了終止發送和接受

          #endif
          }


          else
          {
          ControlState = STALLED;
          }

          pInformation->ControlState = ControlState;

          return Post0_Process();
          }

          ***************(5)**************

          獲取設備描述符以后,主機再一次的復位設備,設備又進入初始狀態。開始枚舉的第二步設置地址。

          void NoData_Setup0(void)
          {
          RESULT Result = USB_UNSUPPORT;
          uint32_t RequestNo = pInformation->USBbRequest;
          uint32_t ControlState;

          if (Type_Recipient == (STANDARD_REQUEST | DEVICE_RECIPIENT)) //設備請求
          {


          else if (RequestNo == SET_ADDRESS) /設置地址
          {
          if ((pInformation->USBwValue0 > 127) || (pInformation->USBwValue1 != 0)
          || (pInformation->USBwIndex != 0)
          || (pInformation->Current_Configuration != 0))

          {
          ControlState = STALLED;
          goto exit_NoData_Setup0;
          }
          else
          {
          Result = USB_SUCCESS;

          #ifdef STM32F10X_CL
          SetDeviceAddress(pInformation->USBwValue0);
          #endif
          }
          }

          ControlState = WAIT_STATUS_IN;

          USB_StatusIn();//準備好發送0字節的狀態數據包SetEPTxCount(ENDP0, 0);

          //vSetEPTxStatus(EP_TX_VALID);建立階段后直接的進入狀態階段

          exit_NoData_Setup0:
          pInformation->ControlState = ControlState;
          return;
          }

          uint8_t In0_Process(void)
          {
          uint32_t ControlState = pInformation->ControlState;

          if ((ControlState == IN_DATA) || (ControlState == LAST_IN_DATA)) //控制狀態
          {
          DataStageIn();//第一次取設備描述符只取一次 當前的狀態變?yōu)閃AIT_STATUS_IN 表明設備等待狀態過程 主機輸出0字節

          ControlState = pInformation->ControlState;
          }

          else if (ControlState == WAIT_STATUS_IN) //設置地址狀態階段進入這個程序
          {
          if ((pInformation->USBbRequest == SET_ADDRESS) &&
          (Type_Recipient == (STANDARD_REQUEST | DEVICE_RECIPIENT)))
          {
          SetDeviceAddress(pInformation->USBwValue0);//設置使用新的地址
          pUser_Standard_Requests->User_SetDeviceAddress();
          }
          (*pProperty->Process_Status_IN)();
          ControlState = STALLED; //終止發送和接受

          }

          else
          {
          ControlState = STALLED;
          }

          pInformation->ControlState = ControlState;

          return Post0_Process();
          }

          uint8_t Post0_Process(void)
          {
          #ifdef STM32F10X_CL
          USB_OTG_EP *ep;
          #endif
          SetEPRxCount(ENDP0, Device_Property.MaxPacketSize);//設置端點0 要接受的字節數

          if (pInformation->ControlState == STALLED)//這種狀態下只接受SETUP命令包
          {
          vSetEPRxStatus(EP_RX_STALL);//終止端點0接受
          vSetEPTxStatus(EP_TX_STALL);//終止端點0發送

          }

          return (pInformation->ControlState == PAUSE);
          }

          ***************(6)*************

          從新地址獲取設備描述符



          上一頁 1 2 3 下一頁

          關鍵詞: STM32USB使用說

          評論


          相關推薦

          技術專區

          關閉
          看屁屁www成人影院,亚洲人妻成人图片,亚洲精品成人午夜在线,日韩在线 欧美成人 (function(){ var bp = document.createElement('script'); var curProtocol = window.location.protocol.split(':')[0]; if (curProtocol === 'https') { bp.src = 'https://zz.bdstatic.com/linksubmit/push.js'; } else { bp.src = 'http://push.zhanzhang.baidu.com/push.js'; } var s = document.getElementsByTagName("script")[0]; s.parentNode.insertBefore(bp, s); })();