AT89C51單片機驅動128x64液晶顯示C語言

AT89C51單片機驅動128x64液晶顯示C語言
****************************************************************/
#include
#define uchar unsigned char
/*****************************************
電路連接
P1------DB0～DB7
P2.0------RS
P2.1------RW
P2.2------E
*****************************************/
#define LCD_DB P1
#define uchar unsigned char
#define uint unsigned int
sbit LCD_RS=P2^0;
sbit LCD_RW=P2^1;
sbit LCD_E=P2^2;
uchar code kk[] = {
//"陜",
0xFE,0x82,0x1A,0xE6,0x4C,0x74,0x44,0xFF,
0x64,0x5C,0x46,0x44,0x0F,0x00,0x01,0x08,
0x08,0x04,0x03,0x00,0x01,0x02,0x04,0x08};
uchar code xi[]={//"西",
0x02,0xFA,0x0A,0x8A,0x7E,0x0A,0x0A,0xFE,
0x8A,0x8A,0xFB,0x02,0x00,0x0F,0x05,0x04,
0x04,0x04,0x04,0x04,0x04,0x04,0x0F,0x00};
uchar code dian[]={//"電",
0x00,0xFC,0x24,0x24,0x24,0xFF,0x24,0x24,
0x24,0xFE,0x04,0x00,0x00,0x01,0x01,0x01,
0x01,0x07,0x09,0x09,0x09,0x09,0x08,0x0E};
uchar code zi[]={//"子",
0x00,0x20,0x21,0x21,0x21,0x21,0xF9,0x25,
0x23,0x21,0x30,0x20,0x00,0x00,0x00,0x04,
0x08,0x08,0x0F,0x00,0x00,0x00,0x00,0x00};
uchar code ke[]={//"科",
0x8A,0x4A,0xFF,0x29,0x49,0x08,0x22,0xCC,
0x80,0xFF,0x40,0x40,0x01,0x00,0x0F,0x00,
0x00,0x01,0x01,0x00,0x00,0x0F,0x00,0x00};
uchar code ji[]={//"技",
0x48,0x48,0xFF,0x28,0x28,0x64,0xA4,0x3F,
0xA4,0x64,0x26,0x04,0x04,0x08,0x07,0x08,
0x08,0x04,0x02,0x01,0x02,0x04,0x08,0x08};
uchar code xue[]={ //"學",
0x20,0x18,0x29,0x2E,0x28,0xA9,0xAE,0x68,
0x2C,0x0B,0x98,0x08,0x01,0x01,0x01,0x01,
0x05,0x09,0x0F,0x01,0x01,0x01,0x01,0x01};
uchar code yuan[]={//"院",
0xFE,0x02,0x1A,0xE6,0x48,0x54,0xD4,0x55,
0xD6,0x54,0x54,0x4C,0x0F,0x01,0x02,0x09,
0x08,0x04,0x03,0x00,0x07,0x08,0x08,0x0E};
uchar code yu[]={//"余",
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,
0xE0,0x70,0x3F,0x1F,0x32,0x60,0xC0,0x80,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x60,0x20,0x10,0x98,0x8C,0x87,0xCB,
0xCD,0x4C,0xFC,0xFC,0x46,0x66,0x66,0x61,
0x63,0x67,0x4E,0x0C,0x0C,0x0C,0x08,0x08,
0x00,0x00,0x00,0x00,0x30,0x3C,0x1E,0x00,
0x20,0x60,0xFE,0xFF,0x00,0x00,0x02,0x06,
0x0E,0x1C,0x18,0x00,0x00,0x00,0x00,0x00};
/******定義函數****************/
void LCD_init(void);//聲明初始化函數
void LCD_write_command(uchar command);//寫指令函數
void LCD_write_data(uchar dat);//寫數據函數
void LCD_disp_char(uchar x,uchar y,uchar dat);//在某個屏幕位置上顯示一
//個字符,X（0-16),y(1-2)
//void LCD_check_busy(void);//檢查忙函數。我沒用到此函數，因?yàn)橥ㄟ^率極低。
void delay(uint n);//延時函數
//********************************
//*******初始化函數***************
void LCD_init(void)
{
LCD_write_command(0x38);//設置8位格式，2行，5x7
LCD_write_command(0x0c);//整體顯示，關光標，不閃爍
LCD_write_command(0x06);//設定輸入方式，增量不移位--------------
LCD_write_command(0x01);//清除屏幕顯示----------------
delay(100);//實踐證明，我的LCD1602上，用for 循環200 次就能可靠完成清屏指令。
}
//********************************
//********寫指令函數***********設置先向1602寫入的數據為地址*
void LCD_write_command(uchar dat)
{
LCD_DB=dat;
LCD_RS=0;//指令
LCD_RW=0;//寫入
LCD_E=1;//允許
LCD_E=0;//產生下降沿
delay(1);//實踐證明，我的LCD1602 上，用for 循環1 次就能完成普通寫指令。
}
//*******************************
//********再寫數據函數*****向1602中寫入數據********
void LCD_write_data(uchar dat)
{
LCD_DB=dat;
LCD_RS=1;//數據
LCD_RW=0;//寫入
LCD_E=1;//允許
LCD_E=0;//產生下降沿
delay(1);
}
void writeDataLcd(unsigned char dat)// 寫入數據
{
LCD_RS=1; //RS置1 (運算后P5=xxx1 xxxx,即RS=1其他位狀態不變）
LCD_RW=0; //RW清0 (運算后P5=xx0x xxxx, 即RW=0其他位狀態不變)
LCD_E=0; //使能E清0 (運算后P5=xxxx 0xxx, 即E=0其他位狀態不變)
P1 = dat; //送數據到P2OUT準備輸出進入1602，等E下降沿來即可進入1602.
LCD_E=1; //使能E置1，P5OUT= xxxx xxxx+0000 1000=xxxx1xxx，E=1.
delay(10);
LCD_E=0; //使能E清0，這樣E從1變0，產生一個下降,寫入命令到1602。
}

//********************************
//*******顯示一個字符函數*********
void LCD_disp_char(uchar x,uchar y,uchar dat)
{

if(y>=64)
{
y=y-1;}

LCD_write_command(0x40|y);
delay(10);
LCD_write_command(0xb8|x);
LCD_write_data(dat);
}
//********************************
/*******檢查忙函數*************
voidLCD_check_busy()
//實踐證明，在我的LCD1602 上，檢查忙指令通
過率極低，以至于不能正常使用LCD。因此我沒有再用檢查忙函數。而使
do//用了延時的方法，延時還是非常好用的。我試了一下，用//
{LCD_E=0; //for 循環作延時，普通指令只要1次循就可完成。清屏指令
LCD_RS=0; //要用200次循環便能完成。
LCD_RW=1;
LCD_DB=0xff;
LCD_E=1;
while(LCD_DB^7==1);
｝
******************************/
//********延時函數***************
void delay(uint n)
{ uint i;
uchar j;
for(i=n;i>0;i--)
for(j=0;j<2;j++); //在這個延時循環函數中我只做了2次循環，
} //實踐證明我的LCD1602 上普
//通的指令只需1次循環就能可靠完成。
//*******************************
//*********主函數*****************
void main(void)
{
while(1)
{
uint i=0;
LCD_init();
while(1)
{

for (i=0;i<12;i++)//shan
{
LCD_disp_char(0,i,kk[i]);
delay(1);
}
for (i=12;i<24;i++)
{
LCD_disp_char(1,i-12,kk[i]);
delay(1);
}
for (i=0;i<12;i++)//xi
{
LCD_disp_char(0,i+12,xi[i]);
delay(1);
}
for (i=12;i<24;i++)
{
LCD_disp_char(1,i,xi[i]);
delay(1);
}
for (i=0;i<12;i++)//dian
{
LCD_disp_char(0,i+24,dian[i]);
delay(1);
}
for (i=12;i<24;i++)
{
LCD_disp_char(1,i+12,dian[i]);
delay(1);
}
for (i=0;i<12;i++)//zi
{
LCD_disp_char(0,i+36,zi[i]);
delay(1);
}
for (i=12;i<24;i++)
{
LCD_disp_char(1,i+24,zi[i]);
delay(1);
}