RS485總線的深層理解

輸入阻抗是多節點的一個分析點

RS-485標準采有用平衡式發送，差分式接收的數據收發器來驅動總線，具體規格要求：
1. 接收器的輸入電阻RIN≥12kΩ
2. 驅動器能輸出±7V的共模電壓
3. 輸入端的電容≤50pF
4. 在節點數為32個，配置了120Ω的終端電阻的情況下，驅動器至少還能輸出電壓1.5V（驅動負載為54Ω，終端電阻的大小與所用雙絞線的參數有關）
5. 接收器的輸入靈敏度為200mV（即（V+）-（V-）≥0.2V，表示信號“1”；（V+）-（V-）≤-0.2V，表示信號“0”）注意！！V+ 我們一般說的A，V-我們一般說的是B；
　因為RS-485的遠距離、多節點（32個）以及傳輸線成本低的特性，使得EIA RS-485成為工業應用中數據傳輸?shù)氖走x標準。

1. 在RS485通信系統中，是否需要加終端匹配電阻分析：

引用MAXIM官網上的一篇應用筆記，原文如下

l No Termination（http://www.maxim-ic.com.cn/appnotes.cfm/an_pk/1090）

The first approach in minimizing power consumption is to eliminate termination resistors altogether. This option is available only for short cables and low data rates, which allow reflections to settle before data is sampled in the receiver. As a rule of thumb, no termination is needed when the rise time of a signal is at least four times longer than the one-way propagation delay through the cable. In the following steps, this rule is employed to calculate the maximum usable length for an unterminated cable:

Step 1. For the cable in question, find the one-way velocity of propagation, usually provided by cable manufacturers as a percentage of the speed of light in free space (c = 3x108 m/s). A typical value for standard insulated PVC cable (consisting of a #24 AWG twisted pair) is 8in/ns.

Step 2. For the RS-485 transceiver, find its minimum rise time (tr min) from the data-sheet specifications. A MAX3471, for example, specifies 750ns.

Step 3. Divide the minimum rise time by 4. For the MAX3471, tr min/4 = 750ns/4 = 187.5ns.

Step 4. Calculate the maximum cable distance for which no termination is required: 187.5ns(8in/ns)(1ft/12in) = 125ft.

原文大致描述了在什么情況下可以不添加終端匹配電阻，當信號的轉換時間（上升沿時間）超過電信號沿總線單向傳輸所需時間的4倍以上時可以不加匹配電阻。例如，信號傳輸速率為0.2m/ns (24AWG PVC電纜)，對于MAX3417下降時間為750ns，則只要線纜長度<37m就可以不加終端匹配。（注：有的RS485芯片具有限擺率功能（上升沿時間長），有的不具有此功能（上升沿時間短），具有此功能的芯片一般傳輸速率較低250kbps或500kbps，上升沿時間Tr>200ns,具體值請參考datasheet。）具有限擺率功能的器件有：MAX3082、MAX3085、MAX3060、MAX3061 、SP3072、SP3075、SP3082、SP3085等。

上拉、下拉問題：

1. 在RS485通信系統中，是否需要加上、下拉電阻分析：

引用MAXIM官網上的一篇應用筆記，原文如下：

Failsafe (http://www.maxim-ic.com.cn/appnotes.cfm/an_pk/1090)
For RS-485 receiver inputs between -200mV and +200mV, the output is undefined. That is, if the differential voltage on the RS-485 side of a half-duplex configuration is 0V, and no master transceiver is driving the line (or a connection has come loose), then a logic "high" output is as probable as a logic "low." To ensure a defined output under these conditions, most of todays RS-485 transceivers require failsafe bias resistors: a pullup resistor on one line (A) and a pulldown on the other line (B), as shown in Figure 1. Historically, the failsafe bias resistors on most schematics were labeled 560Ω, but to reduce power loss (when terminating one end only) this value can be increased to approximately 1.1kΩ. Some designers terminate both ends with resistor values between 1.1kΩ and 2.2kΩ. The trade-off is noise immunity versus current draw.

Maxims MAX3080 and MAX3471 family of transceivers solved both of these problems by specifying a precise receiver-threshold range of -50mV to -200mV, thereby eliminating the need for failsafe bias resistors while complying fully with the RS-485 standard. These parts ensure that 0V at the receiver input produces a logic "high" output. Further, this design guarantees a known receiver-output state for the open- and shorted-line conditions.

所以當所有的RS485節點處于接收狀態時，總線狀態不穩定會出現錯誤數據。

解決方法有二：

1. 加上、下拉電阻，來避免總線錯誤數據。電阻的大小要滿足總線差分電壓>200mV 。

2. 使用具有失效保護的RS485芯片-200mV < Vth <-50mV。具有實效保護功能的器件有：MAX3082、MAX3085、MAX3060、MAX3061、SP3072、SP3075、SP3082、SP3085等。

我們知道A>B，200mv，A-B阻抗120R，由此知道電流I；可以算出上拉、下拉電阻是多少。