用于MAX7456隨屏顯示器SPI

讀字節操作程序

讀字節操作(圖2)程序如下所示，與上述程序類似。首先發送地址，然后發送時鐘從MISO讀回?cái)?shù)據。

/*************************************************************************************** spiReadReg** Reads an 8-bit register with the SPI port.* Data is returned. **************************************************************************************/unsigned char spiReadReg (const unsigned char regAddr){unsigned char SPICount;                                       // Counter used to clock out the dataunsigned char SPIData;                  SPI_CS = 1;                                                   // Make sure we start with active-low CS highSPI_CK = 0;                                                   // and CK lowSPIData = regAddr;                                            // Preload the data to be sent with Address and DataSPI_CS = 0;                                                   // Set active-low CS low to start the SPI cyclefor (SPICount = 0; SPICount  8; SPICount++)                  // Prepare to clock out the Address and Data{if (SPIData  0x80)SPI_MOSI = 1;elseSPI_MOSI = 0;SPI_CK = 1;SPI_CK = 0;SPIData = 1;}                                                             // and loop back to send the next bitSPI_MOSI = 0;                                                 // Reset the MOSI data lineSPIData = 0;for (SPICount = 0; SPICount  8; SPICount++)                  // Prepare to clock in the data to be read{SPIData =1;                                               // Rotate the dataSPI_CK = 1;                                                 // Raise the clock to clock the data out of the MAX7456SPIData += SPI_MISO;                                        // Read the data bitSPI_CK = 0;                                                 // Drop the clock ready for the next bit}                                                             // and loop backSPI_CS = 1;                                                   // Raise CSreturn ((unsigned char)SPIData);                              // Finally return the read data}

自動遞增模式下的寫字節操作程序

自動遞增模式下的寫字節操作(圖3)程序如下所示，與和上述單字節寫程序類似。首先發送地址，然后發送時鐘從MISO讀回?cái)?shù)據。

/*************************************************************************************** spiWriteRegAutoIncr** Writes to an 8-bit register with the SPI port using the MAX7456's autoincrement mode**************************************************************************************/void spiWriteRegAutoIncr(const unsigned char regData){unsigned char SPICount;                                       // Counter used to clock out the dataunsigned char SPIData;                                        // Define a data structure for the SPI data.SPI_CS = 1;                                                   // Make sure we start with active-low CS highSPI_CK = 0;                                                   // and CK lowSPIData = regData;                                            // Preload the data to be sent with Address and DataSPI_CS = 0;                                                   // Set active-low CS low to start the SPI cyclefor (SPICount = 0; SPICount  8; SPICount++)                  // Prepare to clock out the Address and Data{if (SPIData  0x80)SPI_MOSI = 1;elseSPI_MOSI = 0;SPI_CK = 1;SPI_CK = 0;SPIData = 1;}                                                             // and loop back to send the next bit   SPI_MOSI = 0;                                                 // Reset the MOSI data line}

自動遞增模式下寫顯示存儲器的程序

自動遞增模式下寫顯示存儲器的程序如下，程序使用稱為 "data"的全局變量數組。定義如下：

extern volatile unsigned char data[DATA_BUF_LENGTH];DATA_BUF_LENGTH = 968

調用程序時，data[]包含顯示存儲器內容，格式如下：

data[0] = ignored (contains a command byte used by the EV kit GUI software)data[1] = character byte 1data[2] = attribute byte 1data[3] = character byte 2data[4] = attribute byte 2etc.

自動遞增模式通過寫0xFF結束，所以該模式下不能向顯示寄存器寫0xFF。如果需要寫OxFF，可以采用單字節寫指令。

/*************************************************************************************** spiWriteCM** Writes to the Display Memory (960 bytes) from "data" extern.* 960 = 16 rows × 30 columns × 2 planes {char vs. attr} screen-position-indexed memory**************************************************************************************/void spiWriteCM()                                               // On entry: global data[1..960]// contains char+attr bytes   // (optionally terminated by 0xFF data)// First, write data[1,3,5,...] Character plane;// MAX7456 WriteReg(0x05,0x41)// "Character Memory Address High";// 0x02:Attribute bytes; // 0x01:character memory address msb{volatile unsigned int Index = 0x0001;                        // Index for lookup into// data[1..960]                    spiWriteReg(DM_ADDRH_WRITE,0x00);                            // initialise the Display Memory high-bytespiWriteReg(DM_ADDRL_WRITE,0x00);                            // and the low-bytespiWriteReg(DM_MODE_WRITE ,0x41);                            // MAX7456 WriteReg(0x04,0x41) "Display Memory Mode";// 0x40:Perform 8-bit operation; 0x01:AutoIncrementDo                                                           // Loop to write the character data{if (data[Index] == 0xFF) {                                // Check for the break characterbreak; }                                             // and finish if foundspiWriteRegAutoIncr(data[Index]);                         // Write the characterIndex += 2;                                               // Increment the index to the next character, // skipping over the attribute  } while(Index  0x03C1);                                     // 0x03C1 = 961// and loop back to send the next characterspiWriteRegAutoIncr(0xFF);                                   // Write the "escape character" to end AutoIncrement 
				
            

				
					
					
				
			
                
			
							

                
			            

                            	              			              			              			上一頁
	              			              			1
              		              			              		              	              				              				2
              					              				              			              		              	              				              				3
              					              				              			              		              	              				              				4
              					              						              						              				下一頁