AD轉換的數碼管顯示

#includereg52.h>//頭文件#define uint unsigned int//宏文件#define uchar unsigned char//宏文件uchar num;//變量void delay3(uint z);//延時定義void dissy();//延時函數定義sbit ge=P3^2;//個位定義sbit shi=P3^3;//十位定義sbit bai=P3^4;//百位定義sbit ad_cs=P2^3;//片選端sbit ad_wr=P3^6;//寫數據端sbit ad_rd=P3^7;//讀數據端sbit pian=P2^6;//鎖存器片選void add();//ad轉換子函數void delay(uint i);//延時子函數申明uchar code table[]={0xc0,0xf9,0xa4,0xb0,0x99,0x92,0x82,0xf8,0x80,0x90,0x88,0x83,0xc6,0xa1,0x86,0x8e};//數組/************主函數**********/void main(){while(1){add();//調用AD轉換子函數dissy();//數碼管顯示子函數  }   }/************AD轉換子函數**********/void add()//AD轉換子函數{uchar i;ad_cs=1;//將片選關閉ad_cs=0;//將片選打開ad_wr=1;//寫數上升沿ad_wr=0;//寫數下降沿ad_wr=1;//寫數上升沿P1=0xff;//送數到P0口ad_rd=1;//讀數上升沿delay(25);//延時一會兒ad_rd=0;//讀數下降沿//////**************因?yàn)锳D轉換時間周期長，

我現在的數碼管沒有采用鎖存器，AD轉換時間大于顯示時間，

所以顯示時會閃爍，解決此問題方法是，連續調用了顯示子程序七次，

這樣顯示時就和AD轉換時一至，顯示出來的數就不閃了********************//////for(i=0;i7;i++)                //調用7次，相當于delay(255)void dissy();//////**********************************//////num=P1;//將數給計數器num}/************顯示子函數**********/void  dissy()//顯示子函數{ P0=table[num/100];//百位顯示數據bai=0;//百位打開delay(14);//延時一會bai=1;//關閉百位P0=table[num%100/10];//十位顯示數據shi=0;//十位打開delay(14);//延時一會shi=1;//關閉十位P0=table[num%10];//百位顯示數據ge=0;//關閉十位delay(14);//延時一會ge=1;//關閉十位}/**************延時子函數*************/void delay(uint i)//延時函數      {uint j,k;//定義變量for(j=i;j>0;j--)//外循環for(k=30;k>0;k--);//內循環}