STC單片機做的電子表C51程序

電路很簡單我就不畫了，是stc系列的單片機做的，顯示部分就是2個74hc573芯片連到P1口，然后用p3.0控制段選，按鍵的定義程序里有說明。很容易就能搭出來，下圖是效果圖，自己用萬用板焊的，技術不行。到處都是飛線呵呵，請大家多多指教

程序的c51語言完整版本的下載地址：http://www.51hei.com/f/biaoc4.rar

#includestc90.h>#define uchar unsigned char#define uint unsigned intuchar d0,ss,gs,sf,gf,sm,gm;uchar e1,e2,e3,e4,e5,e6;uchar s1,q1;uchar shi,fen,miao;// 8 4 2 1 8 4 2 1  // h g f e d c b a//效正 累加數98 跑1320秒 實際1316//當前已走秒數 乘以 當前累加數 除以除以實際秒數 等于 累加數應得值uchar code num[]={0x3f,0x06,0x5b,0x4f,0x66,0x6d,0x7d,0x07,0x7f,0x6f,0x80};//0-9 點uchar code wes[]={0x7f,0xbf,0xdf,0xef,0xf7,0xfb,0xfd,0x7f};//1-8位sbit dua=P3^0;sbit laba=P3^1;sbit a1=P3^2;//時間設置sbit a2=P3^3;//鬧鐘設置sbit a3=P3^4;//按鍵+sbit a4=P3^5;//按鍵-sbit a5=P3^7;//返回 啟動鬧鐘void weiduan(uchar z,uchar x); //位段 函數void chushi();    //初始化函數void shijian();   //時間顯示函數void shjianbata();//測試時間函數void shezhi();    //時間設置函數void naozhong();  //鬧鐘這是函數void shu();       //時間最大值限制函數void delay(uchar d1);//延時函數//...................................................................void main(){ chushi(); //初始化時間TH0=(65535-40000)/256;//定時器裝初值TL0=(65535-40000)%256;ET0=1;//開定時器0中斷TR0=1;//啟動定時器0EA=1; //打開總中斷l(xiāng)aba=1;while(1){  shijian(); //調用時間顯示函數 顯示時間 if(a1==1){if(a2==1){if(a3==1){if(a4==1)

{ weiduan(1,10);delay(5);weiduan(3,10);delay(5);weiduan(5,10);delay(5); }}}}if(a1==0){delay(100);if(a1==0){shezhi();}}if(a2==0){delay(100);if(a2==0){naozhong();}}//調用鬧鐘設置函數if(a5==0){delay(100);{if(a5==0){while(1)

{if(q1==0){q1=1;break;}else{q1=0;break;}}while(a5==0);delay(100);}}}if(a2==0){delay(100);if(a2==0){naozhong();}    }if(q1==1){weiduan(6,0);delay(20);if(fen==e2)

{if(shi==e1){laba=0;}}if(fen!=e2){laba=1;}  }else{laba=1;}}}//...................................................................void naozhong(){while(1){   ss=e1/10;gs=e1%10;  sf=e2/10;gf=e2%10;   sm=e3/10;gm=e3%10;delay(10);weiduan(0,ss);delay(10);weiduan(1,gs);delay(10);weiduan(2,sf);delay(10);     weiduan(3,gf);delay(10);weiduan(4,sm);delay(10);weiduan(5,gm);delay(10);if(a1==0){delay(100);if(a1==0){while(a1==0);delay(20);break;}}if(a2==0){delay(100);while(a2==0);delay(20);s1++;}if(s1==3){s1=0;}if(s1==1){weiduan(0,10);delay(5);weiduan(1,10);delay(5);if(a3==0){delay(20);if(a3==0){e1++;}while(a3==0);delay(100);}if(a4==0){delay(20);if(a4==0){e1--;}while(a4==0);delay(100);}}if(s1==2){weiduan(2,10);delay(5);weiduan(3,10);delay(5);if(a3==0){delay(20);if(a3==0){e2++;}while(a3==0);delay(100);}if(a4==0){delay(20);if(a4==0){e2--;}while(a4==0);delay(100);}}if(s1==0){weiduan(4,10);delay(5);weiduan(5,10);delay(5);if(a3==0){delay(20);if(a3==0){e3++;}while(a3==0);delay(100);}if(a4==0){delay(20);if(a4==0){e3--;}while(a4==0);delay(100);}}}}//.........................................................void shezhi()//時間設置函數{while(1){   ss=shi/10;gs=shi%10;  sf=fen/10;gf=fen%10;   sm=miao/10;gm=miao%10;shijian();if(a2==0){delay(100);if(a2==0){while(a2==0);delay(20);break;}}if(a1==0){delay(100);while(a1==0);delay(20);s1++;}if(s1==3){s1=0;}if(s1==1){weiduan(0,10);delay(5);weiduan(1,10);delay(5);if(a3==0){delay(20);if(a3==0){shi++;}while(a3==0);delay(100);}if(a4==0){delay(20);if(a4==0){shi--;}while(a4==0);delay(100);}}if(s1==2){weiduan(2,10);delay(5);weiduan(3,10);delay(5);if(a3==0){delay(20);if(a3==0){fen++;}while(a3==0);delay(100);}if(a4==0){delay(20);if(a4==0){fen--;}while(a4==0);delay(100);}}if(s1==0){weiduan(4,10);delay(5);weiduan(5,10);delay(5);if(a3==0){delay(20);if(a3==0){miao++;}while(a3==0);delay(100);}if(a4==0){delay(20);if(a4==0){miao--;}while(a4==0);delay(100);}}}}//...................................................................void zhongduan() interrupt 1   //定時器中斷函數體{  TH0=(65535-40400)/256;TL0=(65535-40400)%256;if(e3>=60)//判斷秒等于或超過60{e2++;   //分鐘加1e3=0;}   //秒數清零if(e2>=60) //判斷分鐘等于或超過60{e1++;   //小時加1e2=0;}   //分鐘數清零if(e1>=24) //判斷小時等于或大于24{e1=0;}   //小時數 清零d0++;//累加數shu(); //調用時間最大值限制函數} //...............................................................void delay(uchar d1)//延時函數{uchar t0,t1;for(t0=d1;t0>0;t0--)for(t1=110;t1>0;t1--);}//.................................................................void weiduan(uchar z,uchar x) //位段選擇函數{  P1=num[x];dua=1;dua=0;P1=wes[z];}//.....................................................................................void shijian()//動態掃描時間顯示函數 帶延時{chushi();//調用時間初始化函數  delay(10);weiduan(0,ss);delay(10);weiduan(1,gs);delay(10);weiduan(2,sf);delay(10);     weiduan(3,gf);delay(10);weiduan(4,sm);delay(10);weiduan(5,gm);delay(10);}//............................................................void shu()   //時間最大限制函數體{  if(d0>=98)  //判斷定時器進入 多少次{d0=0;    //清除累加數miao++;}   //秒數自+if(miao>=60)//判斷秒等于或超過60{fen++;   //分鐘加1miao=0;}   //秒數清零if(fen>=60) //判斷分鐘等于或超過60{shi++;   //小時加1fen=0;}   //分鐘數清零if(shi>=24) //判斷小時等于或大于24{shi=0;}   //小時數 清零}//...................................................................void chushi() //時間初始化{   ss=shi/10;gs=shi%10;  sf=fen/10;gf=fen%10;   sm=miao/10;gm=miao%10;}//.............................................................